[cig-commits] r5344 - mc/3D/CitcomS/trunk/doc/manual

[sue at geodynamics.org]

Author: sue
Date: 2006-11-22 12:25:40 -0800 (Wed, 22 Nov 2006)
New Revision: 5344

Modified:
   mc/3D/CitcomS/trunk/doc/manual/citcoms.lyx
Log:
typo; made references into an itemized list

Modified: mc/3D/CitcomS/trunk/doc/manual/citcoms.lyx
===================================================================
--- mc/3D/CitcomS/trunk/doc/manual/citcoms.lyx	2006-11-22 20:05:23 UTC (rev 5343)
+++ mc/3D/CitcomS/trunk/doc/manual/citcoms.lyx	2006-11-22 20:25:40 UTC (rev 5344)
@@ -1,4 +1,4 @@
-#LyX 1.4.1 created this file. For more info see http://www.lyx.org/
+#LyX 1.4.3 created this file. For more info see http://www.lyx.org/
 \lyxformat 245
 \begin_document
 \begin_header
@@ -1405,7 +1405,7 @@
 \end_layout
 
 \begin_layout Standard
-On Unix or Linux systems, there is a high likelihood that a useable C compiler
+On Unix or Linux systems, there is a high likelihood that a usable C compiler
  is already installed.
  To check, type 
 \family typewriter
@@ -5059,7 +5059,7 @@
 \begin_layout Standard
 In order to facilitate the process of gathering I/O performance data from
  a variety of parallel file systems such as GPFS, PVFS, IBRIX FusionFS,
- you can specify the following parameters in the CitComS input file.
+ etc., you can specify the following parameters in the CitComS input file.
  You may use these to tune the performance of the parallel I/O on your system,
  although in future versions of CitComS this might become unnecessary for
  supported file systems.
@@ -5168,28 +5168,44 @@
 
 \end_deeper
 \begin_layout Standard
-For more details, you can refer to the following references: The list of
- MPI-IO reserved file hints is available on Section 7.2.8 in the MPI-2 reference
- book, which can also be accessed online from 
-\begin_inset LatexCommand \url{http://www-unix.mcs.anl.gov/mpi/mpi-standard/mpi-report-2.0/node182.htm}
+For more details, you can refer to the following references: 
+\end_layout
 
+\begin_layout Itemize
+
+\series bold
+\begin_inset LatexCommand \htmlurl[MPI-2: Extensions to the Message-Passing Interface, section 9.2.8]{www-unix.mcs.anl.gov/mpi/mpi-standard/mpi-report-2.0/node182.htm}
+
 \end_inset
 
-.
- For a list of HDF5 file access properties, refer to Chapter 2, Section
- 7.3, in the 
-\begin_inset LatexCommand \url[HDF5 documentation]{http://hdf.ncsa.uiuc.edu/HDF5/doc/UG/08_TheFile.html}
 
+\series default
+ provides a list of MPI-IO reserved file hints, also available in Section
+ 7.2.8 of the MPI-2 reference book.
+\end_layout
+
+\begin_layout Itemize
+
+\series bold
+\begin_inset LatexCommand \htmlurl[HDF5 documentation]{hdf.ncsa.uiuc.edu/HDF5/doc/UG/08_TheFile.html}
+
 \end_inset
 
-.
- Finally, for a short explanation of raw data chunk caching, you can refer
- to 
-\begin_inset LatexCommand \url{http://hdf.ncsa.uiuc.edu/HDF5/doc/Caching.html}
 
+\series default
+, Chapter 2, Section 7.3, contains a list of HDF5 file access properties.
+\end_layout
+
+\begin_layout Itemize
+
+\series bold
+\begin_inset LatexCommand \htmlurl[HDF5 User's Guide: Data Caching]{hdf.ncsa.uiuc.edu/HDF5/doc/Caching.html}
+
 \end_inset
 
-.
+
+\series default
+ offers a short explanation of raw data chunk caching.
 \end_layout
 
 \begin_layout Standard
@@ -7319,7 +7335,7 @@
 [CitcomS.controller]
 \newline
 mo
-nitoringFrequency = 10    ; how often outputs are created
+nitoringFrequency = 10    ; how often outputs are 
 \newline
 
 \newline