[cig-commits] r18602 - in short/3D/PyLith/trunk/doc/userguide: benchmarks/savageprescott tutorials/subduction

[brad at geodynamics.org]

Author: brad
Date: 2011-06-12 18:25:17 -0700 (Sun, 12 Jun 2011)
New Revision: 18602

Modified:
   short/3D/PyLith/trunk/doc/userguide/benchmarks/savageprescott/savageprescott.lyx
   short/3D/PyLith/trunk/doc/userguide/tutorials/subduction/subduction.lyx
Log:
Changed Cubit to CUBIT for consistency.

Modified: short/3D/PyLith/trunk/doc/userguide/benchmarks/savageprescott/savageprescott.lyx
===================================================================
--- short/3D/PyLith/trunk/doc/userguide/benchmarks/savageprescott/savageprescott.lyx	2011-06-12 22:59:09 UTC (rev 18601)
+++ short/3D/PyLith/trunk/doc/userguide/benchmarks/savageprescott/savageprescott.lyx	2011-06-13 01:25:17 UTC (rev 18602)
@@ -273,7 +273,7 @@
 ), the resolution at the outer boundaries is 20 km.
  An inner region is then put through one level of refinement, so that near
  the center of the mesh the resolution is 10 km.
- All meshes were generated with Cubit.
+ All meshes were generated with CUBIT.
 \end_layout
 
 \begin_layout Description

Modified: short/3D/PyLith/trunk/doc/userguide/tutorials/subduction/subduction.lyx
===================================================================
--- short/3D/PyLith/trunk/doc/userguide/tutorials/subduction/subduction.lyx	2011-06-12 22:59:09 UTC (rev 18601)
+++ short/3D/PyLith/trunk/doc/userguide/tutorials/subduction/subduction.lyx	2011-06-13 01:25:17 UTC (rev 18602)
@@ -368,14 +368,14 @@
 \end_layout
 
 \begin_layout Standard
-We construct the mesh in Cubit by constructing the geometry, prescribing
+We construct the mesh in CUBIT by constructing the geometry, prescribing
  the discretization, runnig the mesher, and then grouping cells and vertices
  for boundary conditions and materials.
  We use the APREPRO programming language within the journal files to enable
  use of units and setting variables for values used many times.
- An appendix in the Cubit documentation discusses the features available
- with APREPRO in Cubit.
- The Cubit commands are in three separate journal files.
+ An appendix in the CUBIT documentation discusses the features available
+ with APREPRO in CUBIT.
+ The CUBIT commands are in three separate journal files.
  The main driver is in the journal file mesh_tri3.jou.
  It calls the journal file geometry.jou to construct the geometry and createbc.jou
  to setup the groups associated with boundary conditions and materials.
@@ -618,7 +618,7 @@
 \family typewriter
  mesh_tri3.exo
 \family default
-) corresponding to the nodeset in Cubit, and a label to the boundary condition
+) corresponding to the nodeset in CUBIT, and a label to the boundary condition
  used in any error messages.
 \end_layout
 
@@ -783,7 +783,7 @@
 \family typewriter
  mesh_tri3.exo
 \family default
-) corresponding to the nodeset in Cubit, and a label to the boundary condition
+) corresponding to the nodeset in CUBIT, and a label to the boundary condition
  used in any error messages.
 \end_layout