[CIG-SHORT] install PyLith on a 64 bit machine

[Brad Aagaard]

Yaru-

I don't see any errors in the config.log you sent. It looks like 
configure completed without any error messages. Is this true? If you ran 
into errors when running "make" please pipe make output to a log file 
"make >& make.log" and send the make.log file.

Brad


yaru wrote:
> Hi Brad,
>   I have installed proj, numpy, nemesis and FIAT. However, I am not able to
> install spatialdata.
> I did the following steps to install spatialdata.
> $run svn co http://geodynamics.org/svn/cig/cs/spatialdata-0.1/trunk
> spatialdata 
> $autoreconf -if
> $configure
> $make
> $make install
> 
> Please also find attached for config.log. Thank you.
> 
> Yaru
> 
> 
> -----Original Message-----
> From: Brad Aagaard [mailto:baagaard at usgs.gov] 
> Sent: Saturday, October 06, 2007 2:04 AM
> To: cig-short at geodynamics.org
> Cc: yaru
> Subject: Re: [CIG-SHORT] install PyLith on a 64 bit machine
> 
> Yaru-
> 
> Please check to make sure nemesis was installed correctly. You should 
> have "nemesis" and "mpinemesis" in $PREFIX/bin.
> 
> In section 3.3.2 of the manual, please note that you will also need to
> install 
> proj (before spatialdata), spatialdata, nemesis, numpy (before FIAT), and 
> FIAT. Your linux distribution probably has binary packages for proj and 
> numpy.
> 
> FIAT is available from http://www.fenics.org/wiki/Download.
> 
> The nemesis tarball is posted on the PyLith download page: 
> http://www.geodynamics.org/cig/software/packages/short/pylith/.
> 
> Spatialdata is also CIG software, but the tarball is not posted on the web 
> page. To checkout the source, run
> svn co http://geodynamics.org/svn/cig/cs/spatialdata-0.1/trunk spatialdata
> You will need to run "autoreconf -if" and "configure" like you do for the
> main 
> PyLith source.
> 
> Brad
> 
> 
> On Thursday 04 October 2007, yaru wrote:
>> Hi All,
>>
>>   I try to install PyLith on my 64 bit machine (Operation System :
>> Scientific Linux 4.4 64-bit). I successfully install PETSC but fail to
>> install PyLith.
>>
>> When I ran
>>  ./configure CXXFLAGS=-DNEW_SECTION --prefix=/data/cig
>> I got the following:
>> checking for a BSD-compatible install... /usr/bin/install -c checking
>> whether build environment is sane... yes checking for gawk... gawk ...
>> ......
>> ...
>> checking for PetscInitialize... yes (C++) checking for petsc.h... yes
>> checking whether we can link a trivial C++ PETSc program... yes checking
>> for PetscInitialize... yes (C++) checking for PETSc/Sieve... yes
>> configure: downloading missing Python dependencies
>> configure: error: cannot download missing Python dependencies See
>> `config.log' for more details.
>>
>> I already upgrade Python to v2.5.1.
>> The config.log is attached. Could someone help me out?
>>
>> Thank you,
>>
>> Yaru
>>
>> ****************************************************
>> Ya-Ju Hsu
>> Institute of Earth Sciences, Academia Sinica
>> 128 Academia Road, Sec. 2, Nankang,
>> Taipei 115, TAIWAN
>> e-mail: yaru at earth.sinica.edu.tw
>> Tel: 886-2-27839910 ext. 415
>> Fax: 886-2-27839871
>> ****************************************************
>