[cig-commits] r18625 - short/3D/PyLith/trunk/doc/userguide/tutorials/3dhex8/quasistatic

[brad at geodynamics.org]

Author: brad
Date: 2011-06-14 15:58:01 -0700 (Tue, 14 Jun 2011)
New Revision: 18625

Modified:
   short/3D/PyLith/trunk/doc/userguide/tutorials/3dhex8/quasistatic/quasistatic.lyx
Log:
Tidy up 3d/hex8.

Modified: short/3D/PyLith/trunk/doc/userguide/tutorials/3dhex8/quasistatic/quasistatic.lyx
===================================================================
--- short/3D/PyLith/trunk/doc/userguide/tutorials/3dhex8/quasistatic/quasistatic.lyx	2011-06-14 22:51:43 UTC (rev 18624)
+++ short/3D/PyLith/trunk/doc/userguide/tutorials/3dhex8/quasistatic/quasistatic.lyx	2011-06-14 22:58:01 UTC (rev 18625)
@@ -604,6 +604,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step04-displ-t200.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset
@@ -839,6 +840,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step05-displ-t40.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset
@@ -975,14 +977,13 @@
 \begin_layout Standard
 In this example and the remainder of the examples in this section, we also
  make use of HDF5 output rather than the default VTK output.
- HDF5 output is a new feature beginning with PyLith version 1.6.0, and it
- provides a more efficient output method (smaller files that take less time
- to write) with the additional advantage that multiple time steps can be
- contained in a single file.
- PyLith also produces XDMF files describing the contents of the HDF5 files,
+ HDF5 output is a new feature beginning with PyLith version 1.6, and it is
+ much more efficient with the additional advantage that multiple time steps
+ can be contained in a single file.
+ PyLith also produces Xdmf files describing the contents of the HDF5 files,
  which allows the files to be read easily by applications such as ParaView.
- Since VTK output is still the default, we must explicitly define the writer
- to use.
+ Since VTK output is still the default, we must change the value from the
+ default.
  Also note that the filename suffix is 
 \family typewriter
 .h5
@@ -1042,11 +1043,7 @@
 \end_layout
 
 \begin_layout Standard
-We need to explicitly define the HDF5 writer for other output as well, since
- it is not the default.
- When specifying output for a subdomain or a fault, this also means we must
- explicitly provide the appropriate writer, which was not necessary for
- VTK output.
+We also set the writer for other output as well, since it is not the default.
  For subdomain output we use:
 \end_layout
 
@@ -1347,7 +1344,7 @@
 h5.
  It will contain final slip information for each earthquake source along
  with slip time information.
- When we have run the simulation, the output HDF5 and XDMF files will be
+ When we have run the simulation, the output HDF5 and Xdmf files will be
  contained in 
 \family typewriter
 examples/3d/hex8/output
@@ -1357,7 +1354,7 @@
 step06
 \family default
 ).
- To open the files in ParaView, the XDMF (
+ To open the files in ParaView, the Xdmf (
 \family typewriter
 .xmf
 \family default
@@ -1379,6 +1376,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step06-displ-t300.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset
@@ -1639,7 +1637,7 @@
 \end_layout
 
 \begin_layout Standard
-When we have run the simulation, the output HDF5 and XDMF files will be
+When we have run the simulation, the output HDF5 and Xdmf files will be
  contained in 
 \family typewriter
 examples/3d/hex8/output
@@ -1679,6 +1677,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step07-displ-vel-t300.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset
@@ -2050,7 +2049,7 @@
 \end_layout
 
 \begin_layout Standard
-When we have run the simulation, the output HDF5 and XDMF files will be
+When we have run the simulation, the output HDF5 and Xdmf files will be
  contained in 
 \family typewriter
 examples/3d/hex8/output
@@ -2077,6 +2076,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step08-strain-displ-t150.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset
@@ -2316,7 +2316,7 @@
 \end_layout
 
 \begin_layout Standard
-When we have run the simulation, the output HDF5 and XDMF files will be
+When we have run the simulation, the output HDF5 and Xdmf files will be
  contained in 
 \family typewriter
 examples/3d/hex8/output
@@ -2343,6 +2343,7 @@
 \align center
 \begin_inset Graphics
 	filename figs/step08-strain-displ-t150.jpg
+	lyxscale 50
 	width 10cm
 
 \end_inset