[CIG-SHORT] Problem configuring pylith
Charles Williams
willic3 at rpi.edu
Fri Jun 6 08:16:10 PDT 2008
Hi Oliver,
In addition to the tetgen.h in externalpackages, you should also have
one in ${PETSC_DIR}/${PETSC_ARCH}/include. If you don't, it wasn't
built correctly by PETSc.
Charles
On Jun 6, 2008, at 10:58 AM, Oliver Boyd wrote:
> I did use --enable-pythia when I built spatialdata. It did turn out
> that when trying to configure pylith that I neglected to set
> PYTHIA_INCDIR. That's been fixed.
>
> Now it says that it can't find tetgen.h. It exists under petsc_dev/
> externalpackages/Tetgen/include, but this include directory doesn't
> get incorporated into CPPFLAGS or any other environment variable.
>
> -----Original Message-----
> From: Brad Aagaard [mailto:baagaard at usgs.gov]
> Sent: Friday, June 06, 2008 9:43 AM
> To: cig-short at geodynamics.org
> Cc: Charles Williams; Oliver Boyd
> Subject: Re: [CIG-SHORT] Problem configuring pylith
>
> Oliver-
>
> If the first case, I am guessing that you didn't build spatialdata
> with
> the --enable-pythia flag. PyLith PyLith checks for both the
> spatialdata
> Python stuff as well as the C++ stuff.
>
> I think Charles is correct about the superfluous -I flag. This is
> probably
> showing up because you used an environment variable in setting
> CPPFLAGS that
> was not set or was misspelled.
>
> Brad
>
>
> On Friday 06 June 2008, Charles Williams wrote:
>> Hi Oliver,
>>
>> I'm not sure why configure isn't finding your installation of
>> spatialdata. Did you do a 'make install' when you installed
>> spatialdata, and is the installation directory in your PYTHONPATH?
>> For the second log, it seems to me that you have a stray '-I' in your
>> CPPFLAGS with no associated directory. I'm not sure, but that might
>> be messing things up. Try removing the last '-I' in your CPPFLAGS
>> and
>> then configure again.
>>
>> Good luck,
>> Charles
>>
>> On Jun 6, 2008, at 9:27 AM, Oliver Boyd wrote:
>>> config.log.1 results from instructions in the pylith manual and
>>> config.log.2 results from the platform specific instructions. As for
>>> the former, why is it trying to download spatialdata after I’ve just
>>> installed it?
>>>
>>> Thanks for your help,
>>> Oliver
>>> <config.log.1><config.log.2>
>>> _______________________________________________
>>> CIG-SHORT mailing list
>>> CIG-SHORT at geodynamics.org
>>> http://geodynamics.org/cgi-bin/mailman/listinfo/cig-short
>>
>> Charles A. Williams
>> Dept. of Earth & Environmental Sciences
>> Science Center, 2C01B
>> Rensselaer Polytechnic Institute
>> Troy, NY 12180
>> Phone: (518) 276-3369
>> FAX: (518) 276-2012
>> e-mail: willic3 at rpi.edu
>
>
>
>
Charles A. Williams
Dept. of Earth & Environmental Sciences
Science Center, 2C01B
Rensselaer Polytechnic Institute
Troy, NY 12180
Phone: (518) 276-3369
FAX: (518) 276-2012
e-mail: willic3 at rpi.edu
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://geodynamics.org/pipermail/cig-short/attachments/20080606/f622ba26/attachment-0001.htm
More information about the CIG-SHORT
mailing list