[CIG-SHORT] Problem configuring pylith

[Matthew Knepley]

Just making sure you really want to enable tetgen. We do not currently use it.

  Matt

On Fri, Jun 6, 2008 at 10:16 AM, Charles Williams <willic3 at rpi.edu> wrote:
> Hi Oliver,
> In addition to the tetgen.h in externalpackages, you should also have one in
> ${PETSC_DIR}/${PETSC_ARCH}/include.  If you don't, it wasn't built correctly
> by PETSc.
> Charles
>
> On Jun 6, 2008, at 10:58 AM, Oliver Boyd wrote:
>
> I did use --enable-pythia when I built spatialdata. It did turn out that
> when trying to configure pylith that I neglected to set PYTHIA_INCDIR.
> That's been fixed.
>
> Now it says that it can't find tetgen.h. It exists under
> petsc_dev/externalpackages/Tetgen/include, but this include directory
> doesn't get incorporated into CPPFLAGS or any other environment variable.
>
> -----Original Message-----
> From: Brad Aagaard [mailto:baagaard at usgs.gov]
> Sent: Friday, June 06, 2008 9:43 AM
> To: cig-short at geodynamics.org
> Cc: Charles Williams; Oliver Boyd
> Subject: Re: [CIG-SHORT] Problem configuring pylith
>
> Oliver-
>
> If the first case, I am guessing that you didn't build spatialdata with
> the --enable-pythia flag. PyLith PyLith checks for both the spatialdata
> Python stuff as well as the C++ stuff.
>
> I think Charles is correct about the superfluous -I flag. This is probably
> showing up because you used an environment variable in setting CPPFLAGS that
> was not set or was misspelled.
>
> Brad
>
>
> On Friday 06 June 2008, Charles Williams wrote:
>
> Hi Oliver,
>
> I'm not sure why configure isn't finding your installation of
>
> spatialdata.  Did you do a 'make install' when you installed
>
> spatialdata, and is the installation directory in your PYTHONPATH?
>
> For the second log, it seems to me that you have a stray '-I' in your
>
> CPPFLAGS with no associated directory.  I'm not sure, but that might
>
> be messing things up.  Try removing the last '-I' in your CPPFLAGS and
>
> then configure again.
>
> Good luck,
>
> Charles
>
> On Jun 6, 2008, at 9:27 AM, Oliver Boyd wrote:
>
> config.log.1 results from instructions in the pylith manual and
>
> config.log.2 results from the platform specific instructions. As for
>
> the former, why is it trying to download spatialdata after I've just
>
> installed it?
>
> Thanks for your help,
>
> Oliver
>
> <config.log.1><config.log.2>
>
> _______________________________________________
>
> CIG-SHORT mailing list
>
> CIG-SHORT at geodynamics.org
>
> http://geodynamics.org/cgi-bin/mailman/listinfo/cig-short
>
> Charles A. Williams
>
> Dept. of Earth & Environmental Sciences
>
> Science Center, 2C01B
>
> Rensselaer Polytechnic Institute
>
> Troy, NY  12180
>
> Phone:    (518) 276-3369
>
> FAX:        (518) 276-2012
>
> e-mail:    willic3 at rpi.edu
>
>
>
>
>
> Charles A. Williams
>
> Dept. of Earth & Environmental Sciences
>
> Science Center, 2C01B
>
> Rensselaer Polytechnic Institute
>
> Troy, NY  12180
>
> Phone:    (518) 276-3369
>
> FAX:        (518) 276-2012
>
> e-mail:    willic3 at rpi.edu
>
>
> _______________________________________________
> CIG-SHORT mailing list
> CIG-SHORT at geodynamics.org
> http://geodynamics.org/cgi-bin/mailman/listinfo/cig-short
>
>



-- 
What most experimenters take for granted before they begin their
experiments is infinitely more interesting than any results to which
their experiments lead.
-- Norbert Wiener